冲压模具工程类 

cutting die, blanking die冲裁模  progressive die, follow (-on)die, progression die 连续模（级进模）  stage die, single die 单工程模 transfer die 传送模 transfer line 传送模生产线 plain die简易模  pierce die冲孔模  forming die成型模    Draw Die拉延模  Deep Drawn Die 深冲模  gang dies复合模  shearing die剪边模  riveting die铆合模  pierce冲孔  forming成型(抽凸,冲凸)  draw hole抽孔  bending折弯  emboss凸点  dome凸圆  semi-shearing半剪  stamp mark冲记号  deburr or coin压毛边  punch riveting冲压铆合  side stretch侧冲压平  reel stretch卷圆压平  groove压线  blanking下料  stamp letter冲字(料号)  shearing剪断  tick-mark nearside正面压印  tick-mark farside反面压印   Soft Tool 软模  Prototype Tool/Prototype Mold 手板模    Prototype Test 软模试制  Metal Prototype Die 五金软模   prototype stamping die冲压软模      Prototype Draw Die 拉延模软模   Prototype Die of BIW 车身软模   Prototype Die Developing of BIW 车身软模开发   Prototype Part of BIW车身软模件   Metal Prototype Part 五金手板  Prototype Stampings 软模冲压件  Metal Stamping 五金冲压

 

冲压模具名称类 

layout 排样图 procedure dwg工程图  die structure dwg模具结构图  press specification冲床规格  die height range适用模高  die height模具高度 shut height闭模高度  feeding height 送料高度 burr毛边  punch wt.上模重量 

五金零件类 

inner guiding post内导柱  inner hexagon screw内六角螺钉  dowel pin固定销  lifter pin顶料销  eq-height sleeves=spool等高套筒  lifter guide pin浮升导料销  guide pin导正销  outer guiding post外导柱  located pin定位销  outer bush外导套 

冲压模具模板类 

top plate上托板（顶板）  top block上垫脚  punch set上模座  punch pad上垫板  punch holder上夹板  stripper pad脱料背板  up stripper上脱料板  die pad下垫板  die holder下夹板  die set下模座  bottom block下垫脚  bottom plate下托板(底板)  stripping plate内外打(脱料板)  outer stripper外脱料板  inner stripper内脱料板  lower stripper下脱料板 

零件类 

deburring punch压毛边冲子  groove punch压线冲子  stamped punch字模冲子  round punch圆冲子  special shape punch异形冲子  bending block折刀  baffle plate挡块  located block定位块  supporting block for location 

定位支承块 

air cushion plate气垫板  air-cushion eject-rod气垫顶杆  trimming punch切边冲子  stiffening rib punch = stinger 加强筋冲子  ribbon punch压筋冲子  reel-stretch punch卷圆压平冲子  guide plate定位板  sliding block滑块

机械类常用英语：冲压模具-零件类 

deburring punch压毛边冲子  groove punch压线冲子  stamped punch字模冲子  round punch圆冲子  special shape punch异形冲子  bending block折刀  baffle plate挡块  located block定位块  supporting block for location 定位支承块 

模具工程常用词汇英汉对照 

figure file, chart file图档  punched hole冲孔  panel board镶块  to cutedges=side cut=side scrap切边  to bending折弯  to pull, to stretch拉伸  Line streching, line pulling线拉伸  engraving, to engrave刻印  upsiding down edges翻边  to stake铆合  design modification设计变更  die block模块  folded block折弯块  sliding block滑块  location pin定位销  die plate 模板

冲压模具工序英文简称 

BL:落料 PI：冲孔 DR：拉伸 FL：翻边 RST:整形 C-PI：侧冲孔 FO：成形 TR：修边    BUR:去毛刺 DO：凸包

stamping part   五金冲压件